PE Mechanical: HVAC and Refrigeration Tutoring Online
Prepare for PE Mechanical HVAC and Refrigeration using psychrometrics, cooling loads, equipment calculations and efficient exam practice.
Hire a tutor for Psychrometrics and HVAC load calculations · Refrigeration systems, equipment and controls · Duct, piping and energy analysis for PE preparationand more...
Request tutor availability and a quote. Or email [email protected].

Since 2008
Established Tutoring Service
~1 min
Average First Response
Specialist Match
For Your Subject & Level
30-Min Trial
Try Tutoring Before a Longer Plan
Online PE Mechanical: HVAC and Refrigeration tutoring with My Engineering Buddy
PE Mechanical: HVAC and Refrigeration preparation integrates thermodynamics, air conditioning, energy transfer, fluid flow and equipment performance. My Engineering Buddy provides paid, live, one-to-one tutoring for candidates reviewing psychrometric properties, sensible and latent loads, refrigeration cycles, ductwork, piping, pumps and control concepts. Tutors help translate a system diagram into a consistent mass and energy balance and explain why an idealized load calculation is not the same as a finished system design. The latest NCEES exam specification and applicable reference handbook determine current examinable scope.
Topics a PE Mechanical: HVAC and Refrigeration tutor can help you learn
Psychrometrics and thermal loads
- Dry-bulb and wet-bulb temperatures
- Humidity ratio and relative humidity
- Sensible and latent heat
- Air mixing processes
- Ventilation and infiltration loads
- Cooling and heating load estimates
Equipment and refrigeration
- Vapor-compression refrigeration cycles
- Evaporators and condensers
- Compressor work and efficiency
- Heat pump performance
- Cooling tower concepts
- Air handling unit fundamentals
Distribution and analysis
- Duct airflow and pressure losses
- Pump and pipe head calculations
- Fan performance curves
- Heat exchanger effectiveness concepts
- Control and economizer sequences
- Equipment selection assumptions
How live one-to-one PE tutoring works
Tell us which topics cause trouble, your engineering background and the permitted exam resources you use. A tutor can demonstrate a fresh example, inspect your calculations for unit or reference errors and then ask you to tackle a changed scenario independently. Practice focuses on recognizing physical assumptions, not memorizing the outcome of a familiar problem.
A tutor might introduce a fictional classroom building served by an air-handling unit with given outdoor and return-air conditions. You determine an approximate mixed-air state and calculate the energy removed by a cooling coil using supplied enthalpies and airflow. The tutor raises the outdoor humidity and asks why a purely sensible heat calculation no longer captures the full coil load. You check the psychrometric state and the needed latent removal conceptually.
Sessions can cover psychrometric charts, refrigeration, coils, fans, pumps, distribution and energy calculations. Share the current NCEES HVAC specification and authorized reference materials. Tutors guide original problems and independent review; HVAC sizing, refrigerant handling, safety and code compliance on live projects require qualified professionals.
Important technical distinctions
Cooling capacity, sensible heat ratio and electrical consumption are different engineering quantities. A unit that meets a steady heat load might still fail humidity, ventilation, part-load or control requirements. Psychrometric calculations need consistent moist-air mass bases, and refrigeration cycle properties must use appropriate states. Duct pressure loss and equipment performance also influence energy use, so an isolated capacity number is not proof of a well-performing HVAC design.
Start with a specified dry-air mass flow and two air-state enthalpies, then calculate a simplified coil heat transfer rate. A tutor can help estimate the sensible component from temperature change and compare it with the total. Add a ventilation fraction and calculate a revised mixing condition. In a separate duct example, review pressure loss and fan power under stated efficiency assumptions. Record which handbook properties support each calculation.
Related PE and engineering subjects
PE (Principles and Practice of Engineering) tutoring provides the broader PE exam context. PE Mechanical: Machine Design and Materials tutoring focuses on machine components and materials, PE Mechanical: Thermal and Fluid Systems tutoring emphasizes thermal-fluid system analysis and Engineering tutoring supplies general engineering mechanics and thermodynamics.
Questions about PE Mechanical: HVAC and Refrigeration tutoring
Can I practice psychrometric chart problems?
Yes, including humidity, mixing and cooling-process calculations.
Can lessons cover refrigeration cycles?
Yes, with original enthalpy, compressor and coefficient-of-performance examples.
Can we review fan and pump curves?
Yes, including distribution losses and power calculations.
Will a tutor approve a real HVAC installation?
No. Real design and safety decisions require independent licensed engineering review.





